FRIHOST FORUMS SEARCH FAQ TOS BLOGS COMPETITIONS
You are invited to Log in or Register a free Frihost Account!


Troubleshooting with a multimeter





khemso
--------------------------------------------------------------------------------

NOTE: This testing applies only to the standard ATX PSU, it does not apply to proprietary PSU's (ie: Dell ) which use a different pinout arrangement for their ATX connectors (non-standard).

If you suspect a part has failed but not sure if it's the PSU, CPU or motherboard at fault, you can use a multimeter to aid in locating the probable cause.

Testing the DC voltages
With the 20-pin ATX connector in the motherboard socket and AC power on, the DC voltages have to be probed from the backside of the connector by inserting the probe tip alongside the wires to contact the connector pins.

Set meter to read 20Vdc. Refer to ATX 20-pin connector pinout chart (below) and put the black probe tip to a GND pin (ie: black wires on pins 15, 16, 17).

With the Red probe tip...
1. Check Pin 9 (Purple, VSB) is about 5V. This is the standby voltage and is always on when the power supply is live to an AC source. If not 5V then problem with PSU, or a possible short circuit in motherboard or a peripheral device has caused the PSU to auto-shutdown.
2. Check Pin 14 (Green, PS_On) should be about 3~5V. If PS_On is zero Volts and VSB okay then disconnect the pc case Power On switch to see if voltage comes up, if so then bad switch.
3. Press the pc case Power On switch and PS_On should drop to ~0V.
If no change, the suspects are faulty switch or CPU. If the motherboards PS_On pins are accessible by removing the pc case's power on leads then short the 2 pins with a light tap from a screwdriver tip to trigger the power on. Another way is to use a jumper wire to short PS_On to GND. If no change in PS_On then probable fault is CPU.

With PS_On at ~0V...
4. Check Pin 8 (Gray, Power_OK) should be 3~5V to signal the CPU that power is okay to start. If not above 2.5V then signal not high enough to trigger CPU for start.
5. Pressing the Reset button (or shorting the reset pins) will make Power_OK go low (0V), and when released should go back up to 3~5V.
(Note, this may not happen if the manufacturer has used a 'soft' method to trigger the Reset.)
NOTE: If CPU doesn't POST when Power is first turned on but does POST when Reset triggered, then the initial power demand (by all devices) is to high for the PSU to handle, need to replace PSU with a better one.

With Power_OK at ~5V...
6. Refer to chart and check voltages are at proper levels on the 20-pin connector and all the peripheral power connectors inside the case.
+3.3v pins 1, 2, 11 (Orange wires)
+5V pins 4, 6, 19, 20, (Red wires)
+12V pin 10 (Yellow wires)
-5V pin 18
-12V pin 12

Note: Depending on the quality of the PSU, there may be nominal voltages detected on the +5V and +12V lines with AC live and pc power off. Always remove AC power, and wait at least 30 seconds to allow residual power to drain before working in pc case.


Testing for Continuity
UNPLUG THE COMPUTER FROM THE AC POWER, and wait 1 minute to allow residual power to drain off.

Set the multimeter to the lowest Ohms ( Ω symbol) value, a typical value is 200.
Touch the probe leads together to zero the meter, note the value if it's not quite zero (live zero), this value will be used to indicate a short circuit during testing. Touch the two probe tips to bare metal inside the pc chasis, should get same zero reading.

Testing the PSU for short and open circuits...
Remove ATX connector from motherboard.
1. Keeping one probe on chasis, use other probe to check PSU's AC ground pin and the DC connectors black wire pins are reading zero. Any value other than zero indicates faulty grounding-replace PSU.
2. Keeping one probe on chasis, use other probe to check the connectors non-black wires are non-zero (if a colored wire reading less than 50 suspect a problem).

Testing the Motherboard for open circuit...
Remove the CPU from motherboard socket before doing this test.
Refer to ATX 20-pin connector pinout chart for GND pin locations. Use PSU's 20-pin connector to familiarize yourself with the board's connector. Only test the GND pins, the multimeter's internal voltage may damage a component connected to the other pins.
3. Keeping one probe on chasis, check GND pins 3,5,7,13,15,16,17 should have the zero reading, any other value suspect a fault-check board is properly installed and repeat test.
If still non-zero remove board and test GND pins again, with one probe touching the metal ring at a mounting hole, if still non-zero then motherboard faulty-replace it with another board.
mwm
http://www.techsupportforum.com/computer/topic/65936-1.html

The above link seems to replect what you have posted here I think. Be careful when posting posts to attian membership. THe admin/moderators on here are quite good and rarelt let this stuff slip through. You'll probably get a negative comment from them about this post...

Be warned...

-mwm
Related topics
Can I create a brand new account in my account?
Windows Tips&tricks!
shutting teh pc d0wnzors
Help?
LOUD Noises when Starting Comp
DOS mode
Windows Vista Official Thread
Window$ XP HIDDEN APPS>>>
Image Magick on vacation?
Help needed using Linux
partition + linux
Troubleshooting Guide !
AMFPHP
i need basic troubleshooting manual
Reply to topic    Frihost Forum Index -> Computers -> Computer Problems and Support

FRIHOST HOME | FAQ | TOS | ABOUT US | CONTACT US | SITE MAP
© 2005-2011 Frihost, forums powered by phpBB.